TradeValley Logo

@2020 Tradevalley.com. All rights reserved

Uygulama Esasları


Not enough ratings

Wholesale Price:

Negotiable


Min. Order: Negotiable
Quantity
PortNo shipping preferences
PackagingNo packaging details

Application basics

1. The roof must be covered with under-tile board or OSB of at least 11 mm thickness. 2. The perimeter of the roof should be lathed with 3 x 5 cm wooden lath. 3. The places where the accessories will be placed except for the Z-profile should be lathed with 3x5 cm wooden laths in accordance with the details. 4. ILDIZBOARDs should be placed on the OSB from bottom to top. 5. The front of the first row of ILDIZBOARDs should be cut considering the lath thickness and the tile will protrude 2-3 cm. The cut ILDIZBOARDs can now stand up to the slats. 6. ILDIZBOARDs must be locked to other ILDIZBOARDs by using locking channels on all four sides. 7. After the roof is completely covered with ILDIZBOARD, it should be laid on the ILDIZBOARDs starting from the bottom, parallel to the vapor balancing eaves and with overlaps of 10 cm. In cases where the wind does not allow, ILDIZBOARDs and vapor balancing cover can be placed on the roof in small sections. The steam stabilizer can be attached to the OSB with nails in some places to prevent the cover from flying off. 8. Tile should be laid from bottom to top. 9. After the first row of tiles is placed, each tile should be screwed to the OSB with 8cm chipboard screws from 3 places above its back jaw. 10.2. The 1st row tiles are placed to cover the back jaw of the 1st row tiles and thus the screws of the 1st row tiles are closed. 11.2. Each tile in the row is screwed from its forehead with a 2.5-3 cm black drywall screw at 4 points, so that the back face of the first row tile and the front of the second row tile are screwed together. The same operations are done in every order as you go up. 12. Ridge Ridge: 2 layers of backboard should be made on top of each other with 3x5 cm wooden laths on the backs. The ILDIZBOARD should be cut to rest against the ridge board. The tiles should also be cut to rest against the ridge board and bend 4-5 cm upwards. After the tiles are brought together on both sides of the backboard, the ridge is closed with a ridge and the ridge ridge is screwed to the ridge board at 50 cm intervals. 13. Z Profile: At the bottom of the chimney and wall, the ILDIZBOARD is cut to lean against the chimney or wall, the tile is cut to bend 5 cm upwards after the chimney and the wall, the cut and the wall is covered with a z-profile, and the z profile is It is nailed, the top of the z profile and the wall between the wall is siliconed. If possible, the top of the z profile should be bent by 1 cm and a slit in the wall should be inserted into the plaster and the top should be silicone. Siliconized places should be covered with the same color sand of the ILDIZBOND finishing set. 14. Fringe Ridge: One more row of 3x5 cm laths should be placed on the lath placed on the roof side eaves. ILDIZBOARD should be cut so that it rests on the laths. Fringe ridge should be placed on the eaves lath and screwed with 50 cm intervals from the sides. 15.Vadi stream: Prepare the stream bed with 3x5 cm laths on both sides of the stream bed with 13 cm between them, place the valley stream accessory between the laths and lay it on the lath by making an ear in the valley stream with 50 cm intervals and nail it from the top. Cut the ILDIZBOARD so that the ILDIZBOARD rests on the slats. Cut the tiles so that the tiles are bent 3-4 cm into the valley stream. 16. Flat Plate: To cover the forehead of the roof, you can cut and bend according to the size of the forehead and cover the forehead with a flat plate. For this, the forehead must be properly covered with wood. You can also create special accessories by cutting and bending the flat sheet where standard accessories do not fit. 17. The tiles in the first row should be nailed to the lath underneath from above and the top of the nails should be touched.
logo

KARYA METAL KİREMİT

Location: yurtiçi ve yurtdışı

Rating: Not enough ratings

Transactions: Not enough information

Response Time: Not enough information

About The Company

1991 yılında Türkiye piyasasına ilk defa metal kiremiti getiren firmayız.13 yıl ithal ettikten sonra tamamen yerli ve milli teknolojiyle Türkiye'de üretime başladık.16 yıldır ,başarılı bir şekilde yurt içinde 100 adet bayi ve yurt dışında 30 adet distribütörümüzle ürünlerimizin satışını gerçekleştirmekteyiz. Ürünlerimiz ; 1) ILDIZBOND METAL KİREMİT : üzeri granül taş kaplı metal kiremit 2)ILDIZBOARD EPS ISI YALITIM PANELİ: metal kiremitle uyumludur, hem ısı yalıtımı hem de metal kiremitin üzerinde rahat yürümenizi sağlar. Detaylı bilgiye www.ildiz.com.tr adresinden ulaşabilirsiniz

Send message to supplier

Live RFQs Live Leads
Live Export Opportunities
Live Export Opportunities
Live Export Opportunities