1. ILDIZBOARD is a thermal insulation panel produced in the same form as ILDIZBOND metal tiles.
2. Many advantages are created when the ILDIZBOARD thermal insulation panel is used under the ILDIZBOND metal tiles.
We can list these advantages as follows.
|The roof must be covered with under-tile board or OSB at least 11 mm thick. Roof perimeter should be lathed with 3 x 5 cm wooden laths. The places where other accessories will be placed except the Z-profile should be lathed with 3x5 cm wooden laths in accordance with the details. ILDIZBOARDs should be stacked on the OSB from bottom to top. The first row of ILDIZBOARDs should be cut considering the thickness of the lath and the tile will protrude 2-3 cm. The cut ILDIZBOARDs can now resist the laths. ILDIZBOARDs should be locked to the others by using locking channels on all four sides. After the roof is completely covered with ILDIZBOARD, the vapor balancing should be laid on the ILDIZBOARDs, parallel to the eaves and overlaps of 10 cm, starting from the bottom. In cases where the wind does not allow, ILDIZBOARDs and vapor balancing cover can be placed on the roof in small sections. The steam stabilizer can be attached to the OSB with nails in some places to prevent the cover from flying off. Tile should be laid from bottom to top. After the first row of tiles is placed, each tile should be screwed to the OSB with 8cm chipboard screws from 3 places above the back jaw. The 2nd row tiles are placed so that the 1st row tiles cover the rear jaw and thus the screws of the 1st row tiles are closed. Each tile in the second row is screwed from the forehead with a 2.5-3 cm black drywall screw at 4 points, so that the back face of the first tile and the front of the second row tile are screwed together. 2 layers of backboard should be made on top of each other with 3x5 cm wooden lath on the backs. The ILDIZBOARD should be cut to rest against the ridge board. The tiles should also be cut to rest against the ridge board and bend 4-5 cm upwards. After the tiles are brought together on both sides of the backboard, the ridge is closed with a ridge and the ridge ridge is screwed to the ridge board at 50 cm intervals. At the bottom of the chimney and wall, the ILDIZBOARD is cut to resist the chimney or the wall, the tile is cut to be bent 5 cm up after the chimney and the wall, the top of the cut and the wall is covered with the z-profile and the z profile is nailed to the wall with 50 cm intervals, the top of the z profile between the wall and the wall is siliconed. If possible, the top of the z profile should be bent by 1 cm, a slit opened on the wall and it should be inserted into the plaster and the top should be silicone. Siliconized places should be covered with sand of the same color of ILDIZBOND retouching set. One more row of 3x5 cm lath should be placed on the lath placed on the roof side eaves. The ILDIZBOARD should be cut to rest on the laths. Fringe ridge should be placed on the eaves lath and screwed with 50 cm intervals from the side. Prepare the stream bed with 3x5 cm laths on both sides of the stream bed with 13 cm between them, place the valley stream profiles between the laths and lay it on the lath by making an ear in the valley stream with 50 cm intervals and nail it from the top. Cut the ILDIZBOARD so that the ILDIZBOARD rests on the slats. Cut the tiles so that the tiles are bent 3.4 cm into the valley stream. To cover the forehead of the roof, you can cover the forehead with a flat plate by cutting and bending it according to the size of the forehead. For this, the forehead must be properly covered with wood. You can also create custom accessories by cutting and bending the flat sheet where standard accessories do not fit. The first row of tiles should be nailed from above to the lath below and the top of the nails should be tapped.|
KARYA METAL KİREMİT
Location: yurtiçi ve yurtdışı
Rating: Not enough ratings
Transactions: Not enough information
Response Time: Not enough information
1991 yılında Türkiye piyasasına ilk defa metal kiremiti getiren firmayız.13 yıl ithal ettikten sonra tamamen yerli ve milli teknolojiyle Türkiye'de üretime başladık.16 yıldır ,başarılı bir şekilde yurt içinde 100 adet bayi ve yurt dışında 30 adet distribütörümüzle ürünlerimizin satışını gerçekleştirmekteyiz. Ürünlerimiz ; 1) ILDIZBOND METAL KİREMİT : üzeri granül taş kaplı metal kiremit 2)ILDIZBOARD EPS ISI YALITIM PANELİ: metal kiremitle uyumludur, hem ısı yalıtımı hem de metal kiremitin üzerinde rahat yürümenizi sağlar. Detaylı bilgiye www.ildiz.com.tr adresinden ulaşabilirsiniz